ZX106-QSH 090-ST breakout adapter

2 rowsx90 pins, ( 180pins ) Samtec QSH test board designed on 4 layers PCB board with accessible GND test point

Mates with any height QTH090 Q-Strip Hi-Speed Samtec connector

$155

ZX106-QTH 090-ST breakout adapter

2 rowsx90 pins, ( 180pins ) Samtec QTH test board designed on 4 layers PCB board with accessible GND test point

Meets Altera High Speed Mezzanine HSMC requirements

Mates with any height QSH090 Q-Strip Hi-Speed Samtec connector

$155

ZX106QTH090-HSMC breakout adapter

Designed for the Altera HSMC bus interface, with all accessible single-ended and differential signals routed to the header.

   - 6-layer PCB, via-free design for improved signal integrity.
   - All CLOCKS accessible via onboard IPEX connectors
   - Accessible supply rails for external interface.
   - JTAG, D0 .. D3, PRSNTn signals accessible via 0402 SMD Shunts landing pads
   - Accessible GND test point.
   - Designed for use with Agilent E5381A differential probe or equivalent, single ended scope, or flying lead logic analyzer probe.

Mates with any height QSH090 or ASP-122953-01 connector

$175

ZX107HSMC mezzanine card breakout adapter

Altera HSMC mezzanine card breakout adapter for testing, evaluation, and characterization of Altera HSMC bus interfaces.

   - 6 Layers board design
   - 50Ω trace impedance single ended & 100 Ω differential signaling.
   - All CLOCKS accessible via onboard IPEX connectors.
   - All signals accessible via 0402 SMD landing pads.
   - Accessible GND test point.

Mates with QSH090 / QTH090 ( ASP-122953-01 ASP-122952-01 )

$248

ZX107HSMC-S mezzanine card breakout adapter

ZX107HSMC-S is a mezzanine card designed for the Altera HSMC bus interface. It uses high-performance Samtec connectors to provide access to HSMC signals for testing, debugging, and characterization. The card interfaces directly with a logic analyzer or, when used with ZX132 breakout modules, allows connection of oscilloscope probes for signal analysis and measurement.

   - 6 Layers board design.
   - 50Ω trace impedance single ended & 100 Ω differential signaling.
   - All CLOCKS accessible via onboard IPEX connectors.
   - JTAG, D0..D3 signals accessible via onboard 0402 SMD landing pads.
   - Accessible GND test point .

Mates with QSH090 / QTH090 ( ASP-122953-01 ASP-122952-01 ) connectors

$268

QSH - QTH Series Samtec breakout adapter 0.5mm pitch

2 × 90-pin Samtec QSH/QTH Test Board designed on a 4-layer PCB with easily accessible test points for signal probing, measurement, and characterization.

The board mates with Samtec QSH090 and QTH090 Q-Strip® high-speed connectors of any supported stack height and form factor, providing access to both single-ended and differential pairs signals.

Samtec QSH/QTH series breakout adapters are available in three form factors, as listed below. All modules provide full access to the connector pins through onboard header pins while maintaining excellent signal integrity.

Key Features

   - 2 × 90-pin Samtec QSH/QTH breakout and test board
   - 4-layer PCB design with accessible test points
   - Compatible with Samtec QSH090 and QTH090 Q-Strip® high-speed connectors
   - Supports both single-ended and differential signal measurements
   - Full connector pin breakout via onboard header pins
   - Excellent signal integrity performance
   - Insertion loss better than −2 dB at 3 GHz
   - Ideal for high-speed signal testing, validation, and characterization
   - Best-in-class test and measurement solution for high-speed applications and signal integrity analysis